Skip to content

Install | Hitch Step

Step-by-Step Installation of the Owl Hitch Step on a Sprinter Van

Step 1: Check for Pre-Drilled Holes

  1. Inspect your Sprinter Van’s hitch:
    • Before starting, check if your Sprinter Van has pre-drilled holes on the sides of the factory hitch.
    • Look for two holes on each side of the hitch. These are necessary for installation.
    • If your Sprinter Van doesn’t have these holes, you may need to drill them yourself, though most Sprinter Vans come with these pre-drilled.

Step 2: Prepare the Hitch Step

  1. Install the tread plates:
    • The Owl Hitch Step comes with separate tread plates and small bolts or screws.
    • Secure the tread plates to the hitch step by inserting the screws into the designated holes. Start each screw without fully tightening them.
    • Once all screws are in place, go back and tighten them down. This ensures proper alignment.
    • The tread plates are designed to provide traction, with slightly raised edges for better grip.

Step 3: Slide the Hitch Step onto the Sprinter Van’s Hitch

  1. Align and slide the hitch step:
    • Position the Owl Hitch Step over your Sprinter Van’s factory hitch.
    • Wiggle or adjust the hitch step slightly to ensure it slides on smoothly. If necessary, pull out the ends of the hitch step a little to fit it over the hitch.
    • The back holes on the hitch step will align with the pre-drilled holes in your Sprinter Van’s hitch.

Step 4: Insert the Bolts

  1. Install the side bolts:
    • Insert the 3/8-inch bolts into the side holes of the Owl Hitch Step.
    • Repeat the process for both sides of the hitch.
    • Do not fully tighten these bolts yet. Keep them loose to allow for final adjustments.

Step 5: Install the Rear Bolts

  1. Insert the 5/16-inch bolts:
    • At the back of the Owl Hitch Step, insert the 5/16-inch bolts into the designated holes.
    • Once the bolts are in, add washers and nylock nuts to the inside of each bolt to secure them.
    • Again, leave these bolts slightly loose for now.

Step 6: Tighten the Rear Bolts First

  1. Secure the rear bolts:
    • Now that the bolts are in place, begin by tightening the rear bolts first. These bolts will pull the hitch step securely against the Sprinter Van’s factory hitch.
    • Tightening these bolts first will ensure the hitch step is flat and properly aligned.

Step 7: Tighten the Side Bolts

  1. Secure the side bolts:
    • After tightening the rear bolts, move to the side bolts.
    • Tighten each side bolt securely to ensure the Owl Hitch Step is properly fastened to your Sprinter Van.

Step 8: Check the Fit

  1. Verify the installation:
    • Once all the bolts are tight, check that the Owl Hitch Step is securely fastened to your Sprinter Van.
    • The hitch step should be sturdy with no movement or rattling.
    • Ensure that the step is aligned properly and sits flat against the hitch.

Step 9: Test the Functionality

  1. Test stability and access:
    • Step on the hitch step to ensure it is stable and doesn’t move or flex.
    • Verify that you still have full access to your Sprinter Van’s hitch pin, trailer connector, and any other components located near the hitch.

Final Checks:

  • Ensure all bolts are fully tightened: Go back over all the bolts and double-check that everything is tight.
  • Test for sturdiness: Step on the hitch step a few times to ensure it’s rock solid and doesn’t make any noise or move.

Congrats on installing your new gear from Owl!

Remember, Owl is the #1 manufacturer of Off Road gear and accessories for Adventure vans. We have our van experts standing by at our HQ in Arizona if you have any questions. Our gear for Mercedes Sprinter vans, Ford Transit and Winnebago Revel is Made in the USA, and many products are in stock and ship fast.

More soon,
John Willenborg